AudioCodes Mediant TP-1610 H.323 Manual de usuario Pagina 276
- Pagina / 404
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Mediant 2000 & TP-1610 & TP-260
SIP User's Manual 276 Document #: LTRT-68805
12.2.5 SS7 MTP2 Tunneling ini File Example
For the SS7 MTP2 tunneling ini file example, note the following:
The first ini file acts as an MTP2 tunneling central side (M2UA MGC links).
There are eight SS7 links - four links of type: MTP2 MGC, and four links of type MTP2.
Each pair of links (one MTP2 MGC and one MTP2) defines an MTP2 tunnel.
There is one interface that is used for the M2UA MGC <=> M2UA SG (Signaling
Gateway) connection.
There are four interface IDs defined: one per link (M2UA MGC side).
This file is intended for ITU link variant (E1 trunks).
¾ To load the example SS7 MTP2 tunneling ini files to gateways, take
these 3 steps:
1. Load the ini file that is shown in Figure 12-6 to a tunnel central gateway (MTP2 MGC).
Load the ini file that is shown in Figure 12-7 to a tunnel remote gateway (MTP2 SG);
the MGC gateway connects (over IP) to the SG gateway. For information on loading
an ini file to the gateway, refer to Section 6.2 on page 127.
2. In the MGC gateway, change the parameter ‘SS7_DEST_IP’ to the actual IP address
of the M2UA SG gateway.
3. Change the value of the ‘SyslogServerIP’ parameter in the MGC and SG gateways to
your Syslog server IP address.
Figure 12-6: SS7 MTP2 Tunneling ini File Example - MGC
[TDM BUS configuration]
; 1=aLaw 3=ulaw
PCMLawSelect= 1
;1 - internal, 3 - mvip, 4 - Network, 8 - h110a, 9 - h110b, 10 - Netref
TDMBusClockSource= 1
[Trunk Configuration]
;e1_euro_isdn=1 t1_isdn=2 ;e1_cas_r2=8 (8 for fcd); e1_trans_62=5
ProtocolType = 5
TraceLevel = 0
; acCLOCK_MASTER_ON =1
CLOCKMASTER= 1
;acUSER_TERMINATION_SIDE = 0
TerminationSide = 1
;acEXTENDED_SUPER_FRAME=0
FramingMethod = 0
;acB8ZS = 0 2 for E1_CAS - FCD
LineCode = 0
[SS7]
- User’s Manual Version 5.0 1
- Table of Contents 3
- List of Figures 10
- List of Tables 13
- Reader's Notes 16
- Related Documentation 18
- 1 Overview 19
- 1.3 TP-1610 Overview 20
- 1.4 TP-260 Overview 21
- 1.5 SIP Overview 22
- 1.6 Features 23
- 2 Physical Description 27
- 2.1.2 Optional CPU Board 28
- 2.2.2 on page 31) 29
- RJ-48c Connector and Pinout 32
- 2.3.1 TP-260 LEDs 33
- 3 Installation 35
- Electrical Earthing 39
- 1 2 3 4 5 6 7 8 41
- 3.2 Installing the TP-1610 44
- 3.2.4 Cabling the TP-1610 45
- 3.3 Installing the TP-260 46
- 3.3.3 Installing the TP-260 47
- 3.3.4 Cabling the TP-260 47
- 4 Getting Started 49
- 11.1 on page 247) 50
- 5 Web Management 55
- 5.2.1 User Accounts 56
- 5.6.8.1 on page 98. Note 57
- 5.4.1 Main Menu Bar 60
- 5.4.2 Saving Changes 60
- 5.5 Protocol Management 63
- 5.5.2 Advanced Parameters 64
- 6-10 on page 180) 72
- 5.5.5.4 on page 75 72
- 5.5.5.3 Internal DNS Table 74
- 5.5.5.4 Internal SRV Table 75
- H on page 379) 77
- 5.5.6.2 Tel Profile Settings 79
- 5.5.6.3 IP Profile Settings 80
- 5.6 Advanced Configuration 84
- 12.2.4 on 90
- 12.2.4 on page 272 91
- 5.6.4.2 Configuring Links 92
- 5.6.7 Regional Settings 97
- 5.6.8 Security Settings 98
- 15.7.1 on page 316 104
- 5.7 Status & Diagnostic 106
- Column Name Description 107
- 5.7.1.2 Call Counters 108
- 5-13 on 108
- 5.7.1.3 Call Routing Status 109
- 5-39 shows the possible 110
- 14.2 on page 304 112
- 6-2) to determine 112
- 5.7.4 Device Information 113
- 9.1 on page 229 114
- 5.8 Software Update Menu 115
- 5.8.2 Auxiliary Files 119
- 11.7 on page 262 121
- 5.9 Maintenance 122
- 5.9.2 Saving Configuration 124
- 5.2.1 on page 56 126
- 6.1 Secured ini File 127
- 6.2 Modifying an ini File 127
- 6.3 The ini File Content 128
- 6.4 The ini File Structure 128
- 6.5 The ini File Example 129
- 6.6 Networking Parameters 130
- [NTP UTC Offset] 134
- 6.7 System Parameters 138
- 6.9 Security Parameters 145
- 6.10 RADIUS Parameters 147
- 6.11 SNMP Parameters 148
- 6.13 Voice Mail Parameters 170
- 6.17 Channel Parameters 196
- Web Parameter Name 197
- 5.8.2 on page 119), or via 201
- 7 Using BootP / DHCP 203
- 7.2 Using DHCP 204
- 7.3 Using BootP 205
- 8 Telephony Capabilities 207
- 8.3.1 Fax/Modem Settings 210
- 8.5 ThroughPacket™ 214
- 8.8 Call Detail Report 217
- 8.12 SIP Call Flow Example 223
- 9 Networking Capabilities 229
- 9.3 NAT Support 230
- 9.3.1 STUN 231
- 9.3.3 No-Op Packets 232
- 9.4.2 PPPoE Overview 234
- 9.5 IP Multicasting 235
- 9-1 on page 238 236
- 6-1 on page 130 236
- 9.10 VLANS and Multiple IPs 237
- 9.10.2.1 Operation 239
- 10.1 Gateway Clock Settings 243
- 10.2 ISDN Overlap Dialing 243
- 10.3 Using ISDN NFAS 244
- 10.3.1 NFAS Interface ID 245
- Mediant 2000 248
- 6-2 on page 138 249
- 11.4 Startup Process 251
- 11.5 Using Parameter Tables 253
- 11.5.2 Table Permissions 254
- 11.5.4 Secret Tables 254
- 11.7 Software Upgrade Key 262
- 6 steps: 263
- 14.2 on page 264
- 11.7.5 Abort Procedure 265
- 12 Special Applications 267
- 12.2 SS7 Tunneling 269
- 12.2.2 SS7 Characteristics 270
- 12.2.3 SS7 Parameters 271
- 12.2.4 SS7 Parameter Tables 272
- 12.2.4.3 SS7 Signaling Link 274
- 12.3 QSIG Tunneling 280
- 13 Security 281
- 13.1.1 IKE 282
- 13.1.2 IPSec 282
- 13.1.3.1 IKE Configuration 283
- 13-2 below) are applied 284
- 11.5 on page 284
- 13.1.3.2 IPSec Configuration 286
- 13-4 below) are applied 287
- 11.5 on page 253). Each 287
- 13.2 SSL/TLS 290
- 13.2.3 Secured Telnet 291
- 13.2.5 Client Certificates 293
- 13.3 SRTP 294
- 6-5 on page 147 296
- 13.5 Internal Firewall 298
- 5.6.8.3 on page 101) 299
- 13.6 Network Port Usage 300
- 13.7 Recommended Practices 301
- 13.8 Legal Notice 301
- 14 Diagnostics 303
- 14.2 Syslog Support 304
- 14.2.2 Operation 305
- 15 SNMP-Based Management 307
- 15.1.2 SNMP MIB Objects 308
- 15.2.1 Active Alarm Table 309
- 15.2.2 Alarm History 309
- 15.3 Cold Start Trap 310
- 15.4.1 Total Counters 311
- ♦ dsx1LineCoding 312
- ♦ dsx1LoopbackConfig 312
- ♦ dsx1CircuitIdentifier 312
- 15.6 Traps 314
- 15.7 SNMP Interface Details 315
- 15.7.1 SNMP Community Names 316
- 15.7.2 SNMP v3 USM Users 318
- 15.7.3 Trusted Managers 320
- 15.7.4 SNMP Ports 322
- 15.9 Dual Module Interface 325
- 15.10 SNMP NAT Traversal 326
- 15.11.1 Node Maintenance 327
- 15.11.2 Graceful Shutdown 327
- 16 Configuration Files 329
- ♦ Continuous 330
- ♦ Cadence 330
- ♦ Burst 330
- 16.3 Voice Prompts File 332
- 16.5 User Information File 333
- A.1 General Specifications 335
- A.3 TP-1610 Specifications 339
- A.4 TP-260 Specifications 341
- B Supplied SIP Software Kit 343
- C SIP Compliance Tables 345
- Header Field Supported 346
- C.4 SDP Headers 347
- C.5 SIP Responses 347
- D.2 An Overview of BootP 353
- D.3 Key Features 353
- D.4 Specifications 354
- D.5 Installation 354
- D.9 Log Window 356
- D.10.1 BootP Preferences 358
- D.10.2 TFTP Preferences 358
- D.11.1 Adding Clients 360
- D.11.2 Deleting Clients 360
- D.11.4 Testing the Client 361
- Allocation 365
- (RTCP-XR) 367
- 16.1 on page 329 370
- 16.3 on page 331 371
- 6.1 on page 127 374
- 16.2.1 on page 332 375
- G.2 PSTN Trace Utility 376
- H Release Reason Mapping 379
- Response 380
- I SNMP Traps 383
- I.1.4 Component: SS7#0 388
- I.1.6 Other Traps 391
- I.1.7 Trap Varbinds 392
- HTTP Server 393
- J.2 Linux Operation Systems 394
- K Regulatory Information 397
- Safety Notices 398
- Industry Canada Notice 398
- Digital Device Warnings 398
- FCC Statement 399
- Safety Notice 400
- FCC Digital Device Warnings 403
Relacionado con productos y manuales para Gateways / Controladores AudioCodes Mediant TP-1610 H.323
(52 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales