AudioCodes Mediant 600 Manual de usuario Pagina 148
- Pagina / 568
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SIP User's Manual 148 Document #: LTRT-83303
Mediant 1000 & Mediant 600
Parameter Description
Prefer Routing Table
[PreferRouteTable]
Determines if the 'Tel to IP Routing' table takes precedence over a Proxy for
routing calls.
[0] No = Only Proxy is used to route calls (default).
[1] Yes = The device checks the 'Dest Phone Prefix' and/or 'Source
Phone Prefix' fields in the 'Tel to IP Routing' table for a match with the
Tel-to-IP call. Only if a match is not found, a Proxy is used.
Note: Applicable only if Proxy is not always used (AlwaysSendToProxy = 0,
SendInviteToProxy = 0).
Use Routing Table for
Host Names and
Profiles
[AlwaysUseRouteTabl
e]
Use the internal 'Tel to IP Routing' table to obtain the URI Host name and
(optionally) an IP profile (per call), even if a Proxy server is used.
[0] Disable = Don't use (default).
[1] Enable = Use the internal 'Tel to IP Routing' table.
Note: This domain name is used instead of a Proxy name or IP address in
the INVITE SIP URI.
Always Use Proxy
[AlwaysSendToProxy
]
Determines whether the device sends SIP messages and responses through
a Proxy server.
[0] Disable = Use standard SIP routing rules (default).
[1] Enable = All SIP messages and responses are sent to a Proxy server.
Note: Applicable only if Proxy server is used (i.e., the parameter
IsProxyUsed is set to 1).
Send All INVITE to
Proxy
[SendInviteToProxy]
Determines whether INVITE messages, as a result of Transfer or Redirect
are sent to a Proxy server instead of directly to the URI.
[0] No = (default) INVITE messages from Transfer or Redirect are sent
directly to the URI (according to the Refer-To header in the REFER
message or Contact header in 30x response).
[1] Yes = All INVITE messages, including those generated as a result of
Transfer or Redirect are sent to a Proxy server.
Note: Applicable only if a Proxy server is used and the parameter
AlwaysSendtoProxy is set to 0.
Proxy / Registrar Registration parameters
(Note: The proxy and registrar parameter fields appear only if 'Enable Registration' is enabled.)
Enable Registration
[IsRegisterNeeded]
Enables the device to register to a Proxy / Registrar server.
[0] Disable = device doesn't register to Proxy / Registrar (default) server.
[1] Enable = device registers to Proxy / Registrar server when the device
is powered up and at every user-defined interval (configured by the
parameter RegistrationTime).
Note: The device sends a REGISTER request for each channel or for the
entire device (according to the AuthenticationMode parameter).
Registrar Name
[RegistrarName]
Registrar domain name. If specified, the name is used as the Request-URI in
REGISTER messages. If it isn't specified (default), the Registrar IP address,
or Proxy name or IP address is used instead.
The valid range is up to 49 characters.
- User's Manual 1
- Table of Contents 3
- List of Figures 10
- List of Tables 14
- Reader's Notes 16
- Trademarks 17
- WEEE EU Directive 17
- Customer Support 17
- Related Documentation 18
- 1 Overview 19
- 1.2 Mediant 600 20
- 1.3 SIP Overview 21
- 2 Configuration Concepts 23
- 3 Web-Based Management 25
- 3.3.1 Toolbar 28
- 3.3.2 Navigation Tree 29
- 3.3.3.1 Accessing Pages 32
- 3.3.3.2 Viewing Parameters 32
- 3.3.3.5 Working with Tables 36
- 3.3.5 Working with Scenarios 40
- 3.3.5.3 Editing a Scenario 43
- 3.3.5.6 Deleting a Scenario 46
- 3.3.7 Getting Help 52
- 3.3.8 Using the Home Page 52
- Red: Fan tray failure 57
- 3.3.8.5 Replacing Modules 61
- 3.4 Configuration Tab 64
- [2] PassThrough = N/A 67
- [0] Auth NULL 75
- [1] Auth UNIX (default) 75
- [0] = OAMP 75
- [1] = Media (default) 75
- [0] = OAMP (default) 77
- [1] = Media 77
- [2] = Control 77
- 3.4.2 Media Settings 80
- [2] Bypass 84
- [3] Events Only 84
- 3.4.3 PSTN Settings 96
- 3.4.4 Security Settings 111
- 3.4.5 Protocol Configuration 133
- [0] Disable 135
- [1] Supported (default) 135
- [2] Required 135
- [1] Enable = Enable 143
- [1] Enable = Enabled 150
- [1] SRV = SRV 150
- [2] NAPTR = NAPTR 150
- 3.4.5.1.3 Proxy Sets Table 153
- 5 steps: 154
- 3.4.5.1.4 Coders 157
- • x: Any single digit 163
- 3.4.5.2.3 Metering Tones 182
- 3.4.5.2.5 Keypad Features 184
- 4 steps: 189
- [9] Private = Private 196
- 3.4.5.6.1 Authentication 219
- 3.4.5.6.2 Automatic Dialing 220
- 3.4.5.6.4 Call Forward 222
- 3.4.5.6.6 Call Waiting 225
- Disable (default) 232
- 0 = Disable 234
- 1 = Enable 234
- [0] 0 = ROUTINE (default) 241
- [2] 2 = PRIORITY 241
- [6] 6 = IMMEDIATE 241
- [8] 8 = FLASH-OVERRIDE 241
- 3.4.6 Advanced Applications 244
- [1] Alaw = Alaw (default) 252
- [3] MuLaw = MuLaw 252
- 3.5 Management Tab 253
- 3.5.1.3 Maintenance Actions 262
- 2 steps: 265
- 3.5.2 Software Update 266
- 6 steps: 271
- 3.6.2 Gateway Statistics 283
- 3.6.2.2 Call Routing Status 286
- 3.6.2.3 Registration Status 287
- 3.6.2.5 IP Connectivity 289
- 4 ini File Configuration 291
- 4.2 The ini File Structure 292
- 4.3 Modifying an ini File 296
- 4.4.2 System Parameters 305
- [10] = 100000 307
- [1] = Enable RAI service 307
- [0] = Disabled (default) 313
- 4.4.4 Security Parameters 314
- 4.4.5 RADIUS Parameters 320
- 4.4.6 SNMP Parameters 321
- [0] Disable (default) 326
- [1] Enable 326
- [1] = Enabled 332
- 4.4.9 Voice Mail Parameters 343
- 4.4.10 PSTN Parameters 344
- [1] = User-to-User 350
- [0] = Disable (default) 355
- [1] = Enable 355
- 4.4.14 Channel Parameters 377
- 5 Default Settings 385
- 6.5 Coefficient File 393
- 6.6 Dial Plan File 393
- 6.7 User Information File 395
- 7 IP Telephony Capabilities 397
- 7.2.2.1 T.38 Fax Relay Mode 399
- 7.2.2.5 Fax Fallback 402
- 7.2.3 Supporting V.34 Faxes 404
- 7.3 FXO Operating Modes 406
- 7.3.1.2 Two-Stage Dialing 408
- 7.3.1.4 DID Wink 409
- 7.3.2 Telephone-to-IP Calls 410
- Connectivity and QoS) 415
- 7.7.4 Relevant Parameters 416
- 7.9 Call Detail Record 417
- 7.13 Configuration Examples 423
- PSTN, take this step: 431
- 7.14.3 Call Transfer 438
- 7.14.4 Call Forward 439
- 7.14.5 Call Waiting 440
- 7.14.7 Caller ID 441
- 8 Networking Capabilities 445
- 8.3.1 STUN 447
- 8.4 IP Multicasting 448
- 8.9 VLANS and Multiple IPs 450
- Control: Premium control 453
- Management: Bronze 453
- 9.1 Clock Settings 459
- 9.2 Release Reason Mapping 459
- 9.2.1 Reason Header 460
- 9.3 ISDN Overlap Dialing 463
- 9.4 Using ISDN NFAS 464
- 9.4.1 NFAS Interface ID 465
- 10.1 Conference Server 469
- 10.1.1.1 SIP Call Flow 470
- 10.1.1.5 PSTN Participants 472
- 10.2 Announcement Server 483
- 10.2.2 MSCML Interface 484
- 10.2.2.1 Operation 485
- 10.2.2.6 Relevant Parameters 491
- 10.3 IP-to-IP Transcoding 494
- 11 Tunneling Applications 497
- 11.2 QSIG Tunneling 500
- 12.1 OSN Server Modules 501
- 12.2 Required Working Tools 502
- 13.1 Requirements 509
- 13.3.1 Cabling 519
- 14.1 Requirements 523
- 14.2 Cabling 524
- RedHat™ EL 4+) 534
- 14.5 Installing Linux™ SUSE 544
- 16.1 Mediant 1000 557
- 16.2 Mediant 600 561
- 17 Glossary 565
- Terminal Equipment (ISDN) 567
- Voice Prompts (File) 567
Relacionado con productos y manuales para Gateways / Controladores AudioCodes Mediant 600
(46 paginas)
(44 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales