AudioCodes MP-1FXO Manual de usuario Pagina 197
- Pagina / 390
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SIP User's Manual 5. Web Management
Version 5.0 197 December 2006
5.9 Software Update
The ‘Software Update’ menu enables users to upgrade the MediaPack software by loading
a new cmp file along with the ini and a suite of auxiliary files, or to update the existing
auxiliary files.
The ‘Software Update’ menu comprises two submenus:
Software Upgrade Wizard (refer to Section 5.9.1 below).
Load Auxiliary Files (refer to Section 5.9.2 on page 202).
Note: When upgrading the MediaPack software you must load the new cmp
file with all other related configuration files.
5.9.1 Software Upgrade Wizard
The Software Upgrade Wizard guides users through the process of software upgrade:
selecting files and loading them to the gateway. The wizard also enables users to upgrade
software while maintaining the existing configuration. Using the wizard obligates users to
load and burn a cmp file. Users can choose to also use the Wizard to load the ini and
auxiliary files (e.g., Call Progress Tones) but this option cannot be pursued without loading
the cmp file. For the ini and each auxiliary file type, users can choose to reload an existing
file, load a new file or not load a file at all.
Warning 1: The Software Upgrade Wizard requires the MediaPack to be reset at
the end of the process, disrupting any of its traffic. To avoid
disruption, disable all traffic on the MediaPack before initiating the
Wizard.
Warning 2: Verify, prior to clicking the Start Software Upgrade button that no
traffic is running on the device. After clicking this button a device
reset is mandatory. Even if you choose to cancel the process in the
middle, the device resets itself and the previous configuration
burned to flash is reloaded.
- User’s Manual Version 5.0 1
- Table of Contents 3
- List of Figures 11
- List of Tables 14
- 1 Overview 19
- 1.2 SIP Overview 20
- 1.3 MediaPack Features 21
- 1.3.4 SIP Features 22
- 2.1.1 MP-11x Front Panel 25
- 2.1.2 MP-11x Rear Panel 26
- 2.2.1 MP-124 Front Panel 27
- 2.2.2 MP-124 Rear Panel 28
- 3 Installing the MediaPack 29
- 3.1.4 Mounting the MP-11x 30
- 3.1.5 Cabling the MP-11x 33
- 1 2 3 4 34
- 3.2 Installing the MP-124 36
- 3.2.4 Cabling the MP-124 38
- MP-124 Safety Notice 38
- 4 Getting Started 41
- 4.2.4.1 Access the CLI 44
- 5.6.3 on 47
- 5 Web Management 49
- 5.4.1 Main Menu Bar 53
- 5.4.2 Saving Changes 53
- 5.5 Protocol Management 56
- (default) 59
- Default_Cnonce’ 71
- 5.5.1.3 Coders 72
- 8.3.5 on page 222 73
- [MaxDigits] 74
- Note: Digit Mapping Rules 74
- [TimeBetweenDigits] 74
- 5.5.2.1 General Parameters 76
- 5.5.2.3 Metering Tones 86
- ChargeCode 88
- 5.5.2.4 Keypad Features 89
- NumberMapTel2IP 93
- SourceNumberMapIP2Tel 95
- [AddPhoneContextAsPrefix] 97
- 5.5.5.1 General Parameters 98
- 8.7 on page 99
- 5-17) 101
- [RouteModeIP2Tel] 103
- 5.5.5.4 Internal DNS Table 105
- 5.5.5.5 Internal SRV Table 106
- MediaPack 110
- 5.5.6.2 Tel Profile Settings 111
- TelProfile_ID 112
- Parameter Description 112
- 5.5.6.3 IP Profile Settings 113
- IPProfile_ID 114
- 5.5.7 on page 115) 118
- Authentication_x 119
- 5.5.9.2 Automatic Dialing 120
- 5.5.9.3 Caller ID 121
- CallerDisplayInfoX 122
- EnableCallerID_X 123
- 5.5.9.5 Call Forward 124
- [IsTwoStageDial] 127
- [0] = One-stage dialing 127
- 5.6 Advanced Configuration 137
- 9.6 on 139
- D.3 on page 362 159
- [MinFlashHookTime] 160
- [FlashHookPeriod] 160
- 5.6.4 Regional Settings 166
- 5.6.5 Security Settings 168
- WebAccessList_x 170
- 4 steps: 173
- [ActivityListToLog = ARD] 178
- [ActivityListToLog = NAA] 178
- [ActivityListToLog = SPC] 178
- [SNMPTrapCommunityString] 180
- 5.6.6.3 Configuring SNMP V3 181
- 5.7.1 Gateway Statistics 187
- 5.7.1.2 Call Counters 189
- Counter Description 190
- 5.7.1.3 Call Routing Status 191
- 5.7.3 Device Information 193
- Duplex) 194
- 5.8.3 Resetting a Channel 196
- 5.9 Software Update 197
- 5.9.2 Auxiliary Files 202
- CallProgressTonesFileName 203
- PrerecordedTonesFileName 203
- UserInfoFileName 203
- SaveConfiguration 203
- 5.10 Maintenance 204
- 5.10.2 Saving Configuration 205
- Reader's Notes 208
- 6.1 Secured ini File 209
- 6.2 Modifying an ini File 209
- 6.3 The ini File Structure 210
- 7 Using BootP / DHCP 211
- 7.2 Using DHCP 212
- 7.3 Using BootP 213
- 8 Telephony Capabilities 215
- 8.1.3 Call Transfer 216
- 8.1.4 Call Forward 217
- 8.1.5 Call Waiting 217
- 8.3.1 Fax/Modem Settings 220
- 8.3.4 Supporting V.34 Faxes 221
- 8.4 FXO Operating Modes 223
- 8.4.1.2 Two-Stage Dialing 224
- 8.4.2 Telephone-to-IP Calls 226
- 8.4.2.1 Automatic Dialing 227
- 8.5 ThroughPacket™ 229
- 8.7.3 Relevant Parameters 231
- 8.9 Call Detail Record 232
- 8.12 Configuration Examples 237
- 8.12.2 SIP Call Flow 238
- (Phone connected to FXS) 243
- Dialing Mode’ to ‘Two Stage’ 245
- IsTwoStageDial=1) 245
- 9 Networking Capabilities 247
- 9.2.1 STUN 248
- 9.3 IP Multicasting 249
- 9.4.2 PPPoE Overview 251
- 9.9 VLANS and Multiple IPs 254
- 9.9.2.1 Operation 256
- MediaPack 262
- 10.4 Startup Process 265
- 10.5 Using Parameter Tables 267
- 10.5.2 Table Permissions 268
- 10.5.4 Secret Tables 268
- 12 Security 279
- 12.1.1 IKE 280
- 12.1.2 IPSec 280
- 12.1.3.1 IKE Configuration 281
- 12.1.3.2 IPSec Configuration 284
- 12.2 SSL/TLS 288
- 12.2.3 Secured Telnet 289
- 12.2.5 Client Certificates 292
- 12.3 SRTP 293
- 12.5 Internal Firewall 297
- 12.6 Network Port Usage 299
- 12.7 Recommended Practices 300
- 12.8 Legal Notice 300
- 13 Diagnostics 301
- 13.3 Syslog Support 303
- 13.3.2 Operation 304
- 14 SNMP-Based Management 305
- 14.1.2 SNMP MIB Objects 306
- 14.2.1 Active Alarm Table 307
- 14.2.2 Alarm History 307
- 14.3 Cold Start Trap 308
- 14.5 Total Counters 309
- 14.6 Supported MIBs 309
- 14.7 Traps 312
- 14.8 SNMP Interface Details 313
- 14.8.2 SNMP v3 USM Users 315
- 14.8.3 Trusted Managers 317
- 14.8.4 SNMP Ports 319
- 14.10 SNMP NAT Traversal 322
- 14.11.1 Node Maintenance 323
- 14.11.2 Graceful Shutdown 323
- 15 Configuration Files 325
- Continuous 326
- Cadence 326
- Burst 326
- 15.2.1 PRT File Format 330
- 5-35 on 331
- 15.4 User Information File 332
- 16.1 MP-11x Specifications 333
- 16.2 MP-124 Specifications 336
- Safety and EMC 338
- Configuration 338
- Management and 338
- Maintenance 338
- Ram.cmp files 339
- files and utilities 339
- MIBs Files 339
- Reader’s Notes 340
- B SIP Compliance Tables 341
- B.3 SIP Headers 342
- B.4 SDP Headers 343
- B.5 SIP Responses 344
- C.2 An Overview of BootP 349
- C.3 Key Features 349
- C.4 Specifications 350
- C.5 Installation 350
- Log Window 351
- C.9 Log Window 352
- C.10.1 BootP Preferences 353
- C.10.2 TFTP Preferences 354
- C.11.1 Adding Clients 355
- C.11.2 Deleting Clients 356
- C.11.4 Testing the Client 357
- Allocation 361
- E.2.2 Installation 368
- E.2.3 Initial Settings 368
- F SNMP Traps 375
- Condition: 377
- Corrective Action: 377
- F.1.5 Other Traps 381
- F.1.6 Trap Varbinds 381
- HTTP Server 383
- G.2 Linux Operation Systems 384
- H Regulatory Information 387
- Safety Notices 388
- Telecommunication Safety 388
Relacionado con productos y manuales para Redes AudioCodes MP-1FXO
Redes AudioCodes MEDIAPACK VERSION 6.2 Manual de usuario
(294 paginas)
(294 paginas)
Redes AudioCodes Mediant 800 MSBR Manual de usuario
(81 paginas)
(81 paginas)
Redes AudioCodes Mediant 800 MSBR Manual de usuario
(47 paginas)
(47 paginas)
Redes AudioCodes MP-20x Guía de instalación
(26 paginas)
(26 paginas)
Redes AudioCodes MEDIAPACK VERSION 6.2 Especificaciones
(178 paginas)
(178 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales