AudioCodes MEDIAPACK VERSION 6.2 Manual de usuario Pagina 85
- Pagina / 180
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
User's Manual 6. Configuring the MediaPack
Version 2.2 85 July 2007
Table 6-2: SIP Proxy and Registration Parameters (continues on pages 83 to 86)
Parameter Description
Use Routing Table for
Host Names and Profiles
[[no]always-use-route-
table]
This parameter is applicable only if the proxy server is used.
Valid options include:
Enabled = the domain field of the to header is set to the value determined by the
routing table.
Disabled (default) = the domain field of the to header is set to the proxy.
Note: This parameter does not influence the destination to which the packet is sent.
Always use Proxy
[[no]forceProxy]
If this parameter is enabled, the system always uses the proxy server. If the proxy is
not on-line, the call fails.
Valid options include:
Enabled
Disabled (default)
Registration & Authentication Parameters
Authentication Mode
[[no] authPerGateway]
This parameter describes the authentication mode used to register / authenticate
with a proxy or gateway.
Valid options include:
Per User = gateway registers only a single user and uses this user name and
password for call authentication.
Per Gateway = registers a list of users defined in the SIP Users screen (refer to
Section 'SIP Users' on page 87). The gateway uses the list of users for call
authentication if a proxy or gateway requires authentication. The gateway
attempts to match the “from number” to select a user. If a match is found, this
user is used for authentication. If no user is found, the call fails.
Default User Name
User name used to register and authenticate with a registrar or to authenticate with a
proxy.
This user name is only used if the Authentication Mode parameter is set to Per
Gateway.
Default User Password
Password used to authenticate with a registrar or a proxy.
This password is only used if the Authentication Mode parameter is set to Per
Gateway.
Authentication User
User name used for authentication. If not defined, the user name is used.
- User’s Manual 1
- Table of Contents 3
- List of Figures 7
- List of Tables 9
- Reader's Notes 10
- Customer Support 11
- Trademarks 11
- WEEE EU Directive 11
- Typographical Conventions 12
- Related Documentation 12
- 1 Overview 15
- 1.2 Gateway Description 16
- 1.3 SIP Overview 17
- 1.4 MediaPack Features 18
- 1.4.3 Telephony Capabilities 20
- 1.4.3.1.3 Call Forward 21
- 1.4.3.1.4 Call Waiting 21
- 2.1 Physical Description 23
- 2.1.2 Rear Panel 24
- 3 Installing the MediaPack 27
- 3.3 Mounting the MediaPack 28
- 3.4 Cabling the MediaPack 30
- RJ-45 Connector and Pinout 31
- Connector: 8-pin RJ-45 32
- 4 Initial Configuration 39
- ♦ Dest IP: 0.0.0.0 44
- ♦ Dest Mask: 0.0.0.0 44
- ♦ DHCP: 48
- ♦ PPPoE: 48
- General SIP parameters 54
- SIP users 54
- 5.1 Configuration Concepts 63
- 5.2 Embedded Web Server 64
- 5.2.1 Computer Requirements 65
- 5.2.3 Main Menu Bar 66
- 5.2.5 Dialing Notations 67
- 5.3.1 Logging into the CLI 68
- 5.3.2 CLI Modes 69
- 5.3.3 Navigating in the CLI 70
- Version 2.2 75 July 2007 75
- Version 2.2 77 July 2007 77
- 6.1 Quick Setup 79
- 6.2 Protocol Management 79
- 6.2.1 SIP Gateway 80
- 5.3 on page 68 86
- 6.2.1.3 SIP Users 87
- ¾ To configure SIP users: 87
- 6.2.2 ISDN 88
- ¾ To define a tone-set: 92
- 6.2.2.4 Hunt Logic 98
- 6.2.2.5 Manipulation Tables 98
- 6.2.3 Routing Tables 106
- Destination phone prefix 108
- Source phone prefix 108
- Source IP address 108
- Version 2.2 109 July 2007 109
- 6.2.4 Profile Definitions 110
- MediaPack BRI Series 112
- nte 112
- 6.2.4.2 ISDN Profiles 113
- Version 2.2 117 July 2007 117
- 6.3 Advanced Configuration 118
- Version 2.2 121 July 2007 121
- Parameter Description 121
- 6.3.1.2 PPPoE 122
- 6.3.1.3 Static Routes 123
- ¾ To add static routes: 124
- 6.3.1.4 Dynamic Routes 125
- 6.3.1.5 QoS 126
- ¾ To configure QoS: 127
- 6.3.1.7 Access Control List 131
- 6.3.1.8 NAT 134
- Version 2.2 135 July 2007 135
- 6.3.1.9 RIP 136
- 6.3.1.10 Services 137
- <hh:mm:ss> 139
- 6.3.2 User Management 140
- 6.4.1 System Information 142
- 6.4.2 ISDN Ports Status 143
- 6.5 Software Upgrade 144
- Version 2.2 145 July 2007 145
- <source> 148
- Valid options include: 148
- Version 2.2 153 July 2007 153
- 6.7 Resetting the MediaPack 154
- A MediaPack Applications 155
- A.4.2 Call Transfer 169
- A.4.3 Call Forward 170
- A.4.5 Overlap Receiving 172
- A.4.6 MSN 172
- B MediaPack Startup Process 173
- C Technical Specifications 175
Relacionado con productos y manuales para Redes AudioCodes MEDIAPACK VERSION 6.2
Redes AudioCodes Mediant 800 MSBR Manual de usuario
(14 paginas)
(14 paginas)
Redes AudioCodes MP-201B Manual de usuario
(15 paginas)
(15 paginas)
Redes AudioCodes Mediant 800 MSBR Manual de usuario
(66 paginas)
(66 paginas)
Redes AudioCodes MP-1FXO Manual de usuario
(390 paginas)
(390 paginas)
Redes AudioCodes MEDIAPACK VERSION 6.2 Manual de usuario
(294 paginas)
(294 paginas)
Redes AudioCodes Mediant 800 MSBR Manual de usuario
(81 paginas)
(81 paginas)
Redes AudioCodes Mediant 800 MSBR Manual de usuario
(47 paginas)
(47 paginas)
Redes AudioCodes MP-20x Guía de instalación
(26 paginas)
(26 paginas)
Redes AudioCodes MEDIAPACK VERSION 6.2 Especificaciones
(178 paginas)
(178 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales