AudioCodes MediaPack 114 Manual de usuario Pagina 136
- Pagina / 390
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SIP User's Manual 136 Document #: LTRT-65411
MediaPack Series
Parameter Description
Default Release Cause
[DefaultReleaseCause]
Default Release Cause (to IP) for IP-to-Tel calls when the device initiates
a call release and an explicit matching cause for this release isn't found.
The default release cause is NO_ROUTE_TO_DESTINATION (3).
Other common values include NO_CIRCUIT_AVAILABLE (34),
DESTINATION_OUT_OF_ORDER (27), etc.
Notes:
The default release cause is described in the Q.931 notation and is
translated to corresponding SIP 40x or 50x values (e.g., 3 to SIP 404
and 34 to SIP 503).
For an explanation on mapping PSTN release causes to SIP
responses, refer to ‘Mapping PSTN Release Cause to SIP Response’
on page 336.
Delay After Reset [sec]
[GWAppDelayTime]
Defines the time interval (in seconds) that the device's operation is
delayed after a reset.
The valid range is 0 to 45. The default value is 7 seconds.
Note: This feature helps to overcome connection problems caused by
some LAN routers or IP configuration parameters' modifications by a
DHCP server.
Max Number of Active
Calls
[MaxActiveCalls]
Defines the maximum number of simultaneous active calls supported by
the device. If the maximum number of calls is reached, new calls are not
established.
The default value is the maximum available channels (no restriction on
the maximum number of calls). The valid range is 1 to maximum number
of channels.
Max Call Duration (min)
[MaxCallDuration]
Defines the maximum call duration (in minutes). If this time expires, both
sides of the call are released (IP and Tel).
The valid range is 0 to 35,791. The default is 0 (i.e., no limitation).
Enable LAN Watchdog
[EnableLanWatchDog]
Determines whether the LAN Watch-Dog feature is enabled.
[0] Disable = Disable LAN Watch-Dog (default).
[1] Enable = Enable LAN Watch-Dog.
When LAN Watch-Dog is enabled, the device's overall communication
integrity is checked periodically. If no communication for about 3 minutes
is detected, the device performs a self test.
If the self test succeeds, the problem is logical link down (i.e., Ethernet
cable disconnected on the switch side), and the Busy Out mechanism is
activated if enabled (EnableBusyOut = 1). Lifeline is activated if enabled.
If the self test fails, the device restarts to overcome internal fatal
communication error.
Notes:
Enable LAN Watchdog is relevant only if the Ethernet connection is full
duplex.
LAN Watchdog is not applicable to MP-118.
- User's Manual 1
- Table of Contents 3
- List of Figures 8
- List of Tables 11
- WEEE EU Directive 13
- Customer Support 13
- Trademarks 13
- Related Documentation 14
- 1 Overview 15
- 1.2 MediaPack Features 16
- 1.3 SIP Overview 17
- Reader’s Notes 18
- 2 Configuration Concepts 19
- 3 Web-Based Management 21
- 3.3.1 Toolbar 24
- 3.3.2 Navigation Tree 25
- 3.3.3.1 Accessing Pages 28
- 3.3.3.2 Viewing Parameters 28
- 3.3.3.5 Working with Tables 32
- 3.3.5.1 Creating a Scenario 36
- 3.3.5.3 Editing a Scenario 39
- 3.3.5.6 Deleting a Scenario 42
- 3.3.7 Getting Help 47
- 3.3.8 Using the Home Page 48
- (grey): channel inactive 49
- 3.4 Configuration Tab 52
- [0] = OAMP (default) 65
- [1] = Media 65
- [2] = Control 65
- 3.4.2 Media Settings 67
- [2] Bypass 70
- [3] Events Only 70
- 3.4.3 Security Settings 79
- [1] Enable = Enabled 116
- [0] Disable (default) 116
- [1] Enable 116
- 5 steps: 120
- To the default Proxy 121
- 3.4.4.1.4 Coders 123
- 4 steps: 130
- 3.4.4.2.3 Metering Tones 144
- 3.4.4.2.5 Keypad Features 147
- 3.4.4.6.1 Authentication 175
- 3.4.4.6.2 Automatic Dialing 176
- 3.4.4.6.4 Call Forward 178
- 3.4.4.6.6 Call Waiting 180
- Disable (default) 188
- No = Don't register 189
- Yes = Register 189
- 3.4.5 Advanced Applications 190
- [1] Enable (Bellcore) 194
- [2] Ericsson MD-110 194
- [3] NEC (ICS) 194
- 3.5 Management Tab 198
- 3.5.1.3 Maintenance Actions 207
- 2 steps: 209
- 3.5.2 Software Update 210
- 3.6.2 Gateway Statistics 223
- 3.6.2.1 Call Counters 224
- 3.6.2.2 Call Routing Status 226
- 3.6.2.3 Registration Status 227
- 3.6.2.5 IP Connectivity 228
- 4 ini File Configuration 231
- 4.2 The ini File Structure 232
- 4.3 Modifying an ini File 235
- 4.4.1 Networking Parameters 236
- 4.4.2 System Parameters 244
- [0] = Disabled (default) 251
- 4.4.4 Security Parameters 252
- 4.4.5 RADIUS Parameters 257
- 4.4.6 SNMP Parameters 258
- [1] = Enabled 268
- Port = Port number 268
- UserId = User name 272
- UserPassword = Password 272
- 4.4.8 Voice Mail Parameters 277
- 4.4.9 PSTN Parameters 279
- [66] = TBR21 280
- Npi = Number Plan 297
- Ton = Type of Number 297
- 4.4.12 Channel Parameters 298
- [0] = Disable (default) 299
- [1] = Enable 299
- [1] Enable (default) 304
- 5 Default Settings 305
- 6.4 Coefficient File 312
- 6.5 User Information File 313
- 7 IP Telephony Capabilities 315
- 7.1.1 Configuring SAS 316
- 7.3.2.1 T.38 Fax Relay Mode 319
- 7.3.3 Supporting V.34 Faxes 324
- 7.4 FXO Operating Modes 326
- 7.4.1.1 One-Stage Dialing 327
- 7.4.1.2 Two-Stage Dialing 328
- 7.4.1.4 DID Wink 329
- 7.4.2 Telephone-to-IP Calls 330
- Connectivity and QoS) 335
- 7.11 Call Detail Record 339
- 7.13 Configuration Examples 342
- 7.14.3 Call Transfer 359
- 7.14.4 Call Forward 360
- 7.14.5 Call Waiting 361
- 7.14.7 Caller ID 362
- 8 Networking Capabilities 365
- 8.2.1 STUN 366
- 8.2.3 No-Op Packets 367
- 8.3 IP Multicasting 368
- 8.8 VLANS and Multiple IPs 370
- Control: Premium control 372
- Management: Bronze 372
- 10.1 MP-11x Specifications 381
- 10.2 MP-124 Specifications 384
- 11 Glossary 387
Relacionado con productos y manuales para Gateways / Controladores AudioCodes MediaPack 114
(44 paginas)
(44 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales