AudioCodes MediaPack 114 Manual de usuario Pagina 152
- Pagina / 390
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SIP User's Manual 152 Document #: LTRT-65411
MediaPack Series
The number manipulation is configured in the following tables:
For Tel-to-IP calls:
• Destination Phone Number Manipulation Table for Tel-to-IP Calls
(NumberMapTel2IP ini file parameter)
• Source Phone Number Manipulation Table for Tel-to-IP Calls
(SourceNumberMapTel2IP ini file parameter)
For IP-to-Tel calls:
• Destination Phone Number Manipulation Table for IP-to-Tel Calls
(NumberMapIP2Tel ini file parameter)
• Source Phone Number Manipulation Table for IP-to-Tel Calls
(SourceNumberMapIP2Tel ini file parameter)
Notes:
• Number manipulation can occur before or after a routing decision is
made. For example, you can route a call to a specific Hunt Group
according to its original number, and then you can remove or add a prefix
to that number before it is routed. To determine when number
manipulation is performed, configure the 'IP to Tel Routing Mode'
parameter (RouteModeIP2Tel) described in ''IP to Trunk Group Routing''
on page 163, and 'Tel to IP Routing Mode' parameter (RouteModeTel2IP)
described in ''Tel to IP Routing Table'' on page 160.
• For configuring number manipulation using ini file table parameters
NumberMapIP2Tel, NumberMapTel2IP, SourceNumberMapIP2Tel, and
SourceNumberMapTel2IP, refer to ''Number Manipulation and Routing
Parameters'' on page 289.
¾ To configure the Number Manipulation tables, take these 5 steps:
1. Open the required 'Number Manipulation' page (Configuration tab > Protocol
Configuration menu > Manipulation Tables submenu > Dest Number IP->Tel, Dest
Number Tel->IP, Source Number IP->Tel, or Source Number Tel->IP page item);
the relevant Manipulation table page is displayed (e.g., 'Source Phone Number
Manipulation Table for TelÆIP Calls' page).
Figure 3-68: Source Phone Number Manipulation Table for Tel-to-IP Calls
The figure above shows an example of the use of manipulation rules in the 'Source
Phone Number Manipulation Table for TelÆIP Calls':
• When the destination number is 035000 and source number is 20155, the source
number is changed to 97120155.
- User's Manual 1
- Table of Contents 3
- List of Figures 8
- List of Tables 11
- WEEE EU Directive 13
- Customer Support 13
- Trademarks 13
- Related Documentation 14
- 1 Overview 15
- 1.2 MediaPack Features 16
- 1.3 SIP Overview 17
- Reader’s Notes 18
- 2 Configuration Concepts 19
- 3 Web-Based Management 21
- 3.3.1 Toolbar 24
- 3.3.2 Navigation Tree 25
- 3.3.3.1 Accessing Pages 28
- 3.3.3.2 Viewing Parameters 28
- 3.3.3.5 Working with Tables 32
- 3.3.5.1 Creating a Scenario 36
- 3.3.5.3 Editing a Scenario 39
- 3.3.5.6 Deleting a Scenario 42
- 3.3.7 Getting Help 47
- 3.3.8 Using the Home Page 48
- (grey): channel inactive 49
- 3.4 Configuration Tab 52
- [0] = OAMP (default) 65
- [1] = Media 65
- [2] = Control 65
- 3.4.2 Media Settings 67
- [2] Bypass 70
- [3] Events Only 70
- 3.4.3 Security Settings 79
- [1] Enable = Enabled 116
- [0] Disable (default) 116
- [1] Enable 116
- 5 steps: 120
- To the default Proxy 121
- 3.4.4.1.4 Coders 123
- 4 steps: 130
- 3.4.4.2.3 Metering Tones 144
- 3.4.4.2.5 Keypad Features 147
- 3.4.4.6.1 Authentication 175
- 3.4.4.6.2 Automatic Dialing 176
- 3.4.4.6.4 Call Forward 178
- 3.4.4.6.6 Call Waiting 180
- Disable (default) 188
- No = Don't register 189
- Yes = Register 189
- 3.4.5 Advanced Applications 190
- [1] Enable (Bellcore) 194
- [2] Ericsson MD-110 194
- [3] NEC (ICS) 194
- 3.5 Management Tab 198
- 3.5.1.3 Maintenance Actions 207
- 2 steps: 209
- 3.5.2 Software Update 210
- 3.6.2 Gateway Statistics 223
- 3.6.2.1 Call Counters 224
- 3.6.2.2 Call Routing Status 226
- 3.6.2.3 Registration Status 227
- 3.6.2.5 IP Connectivity 228
- 4 ini File Configuration 231
- 4.2 The ini File Structure 232
- 4.3 Modifying an ini File 235
- 4.4.1 Networking Parameters 236
- 4.4.2 System Parameters 244
- [0] = Disabled (default) 251
- 4.4.4 Security Parameters 252
- 4.4.5 RADIUS Parameters 257
- 4.4.6 SNMP Parameters 258
- [1] = Enabled 268
- Port = Port number 268
- UserId = User name 272
- UserPassword = Password 272
- 4.4.8 Voice Mail Parameters 277
- 4.4.9 PSTN Parameters 279
- [66] = TBR21 280
- Npi = Number Plan 297
- Ton = Type of Number 297
- 4.4.12 Channel Parameters 298
- [0] = Disable (default) 299
- [1] = Enable 299
- [1] Enable (default) 304
- 5 Default Settings 305
- 6.4 Coefficient File 312
- 6.5 User Information File 313
- 7 IP Telephony Capabilities 315
- 7.1.1 Configuring SAS 316
- 7.3.2.1 T.38 Fax Relay Mode 319
- 7.3.3 Supporting V.34 Faxes 324
- 7.4 FXO Operating Modes 326
- 7.4.1.1 One-Stage Dialing 327
- 7.4.1.2 Two-Stage Dialing 328
- 7.4.1.4 DID Wink 329
- 7.4.2 Telephone-to-IP Calls 330
- Connectivity and QoS) 335
- 7.11 Call Detail Record 339
- 7.13 Configuration Examples 342
- 7.14.3 Call Transfer 359
- 7.14.4 Call Forward 360
- 7.14.5 Call Waiting 361
- 7.14.7 Caller ID 362
- 8 Networking Capabilities 365
- 8.2.1 STUN 366
- 8.2.3 No-Op Packets 367
- 8.3 IP Multicasting 368
- 8.8 VLANS and Multiple IPs 370
- Control: Premium control 372
- Management: Bronze 372
- 10.1 MP-11x Specifications 381
- 10.2 MP-124 Specifications 384
- 11 Glossary 387
Relacionado con productos y manuales para Gateways / Controladores AudioCodes MediaPack 114
(44 paginas)
(44 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales