AudioCodes MediaPack 114 Manual de usuario Pagina 239
- Pagina / 390
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Version 5.6 239 November 2008
SIP User's Manual 4. ini File Configuration
Parameter Description
EnableUDPPortTranslatio
n
[0] = Disable UDP port translation (default).
[1] = Enable UDP port translation.
When enabled, the device compares the source UDP port of the first
incoming packet, to the remote UDP port stated in the opening of the
channel. If the two UDP ports don't match, the NAT mechanism is
activated. Consequently, the remote UDP port of the outgoing stream
is replaced by the source UDP port of the first incoming packet.
Note: The NAT mechanism and the IP address translation must be
enabled for this parameter to take effect (DisableNAT = 0,
EnableIpAddrTranslation = 1).
NoOpEnable
Enables or disables the transmission of RTP or T.38 No-Op packets.
[0] = Disable (default)
[1] = Enable
This mechanism ensures that the NAT binding remains open during
RTP or T.38 silence periods.
NoOpInterval
Defines the time interval in which RTP or T.38 No-Op packets are sent
in the case of silence (no RTP / T.38 traffic) when No-Op packet
transmission is enabled.
The valid range is 20 to 65,000 msec. The default is 10,000.
Note: To enable No-Op packet transmission, use the NoOpEnable
parameter.
RTPNoOpPayloadType
Determines the payload type of No-Op packets.
The valid range is 96 to 127 (for the range of Dynamic RTP Payload
Type for all types of non hard-coded RTP Payload types, refer to RFC
3551). The default value is 120.
Note: When defining this parameter, ensure that it doesn't cause
collision with other payload types.
EnableDetectRemoteMAC
Change
Changes the RTP packets according to the MAC address of received
RTP packets and according to Gratuitous Address Resolution Protocol
(GARP) messages.
[0] = nothing is changed.
[1] = If the device receives RTP packets with a different source
MAC address (than the MAC address of the transmitted RTP
packets), then it sends RTP packets to this MAC address and
removes this IP entry from the device's ARP cache table.
[2] = The device uses the received GARP packets to change the
MAC address of the transmitted RTP packets.
[3] = both 1 and 2 options above are used (default).
StaticNatIP
For a description of this parameter, refer to ''Configuring the IP
Settings'' on page 52.
SyslogServerIP
For a description of this parameter, refer to ''Configuring the
Management Settings'' on page 199.
SyslogServerPort
For a description of this parameter, refer to ''Configuring the
Management Settings'' on page 199.
EnableSyslog
For a description of this parameter, refer to ''Configuring the
Management Settings'' on page 199.
- User's Manual 1
- Table of Contents 3
- List of Figures 8
- List of Tables 11
- WEEE EU Directive 13
- Customer Support 13
- Trademarks 13
- Related Documentation 14
- 1 Overview 15
- 1.2 MediaPack Features 16
- 1.3 SIP Overview 17
- Reader’s Notes 18
- 2 Configuration Concepts 19
- 3 Web-Based Management 21
- 3.3.1 Toolbar 24
- 3.3.2 Navigation Tree 25
- 3.3.3.1 Accessing Pages 28
- 3.3.3.2 Viewing Parameters 28
- 3.3.3.5 Working with Tables 32
- 3.3.5.1 Creating a Scenario 36
- 3.3.5.3 Editing a Scenario 39
- 3.3.5.6 Deleting a Scenario 42
- 3.3.7 Getting Help 47
- 3.3.8 Using the Home Page 48
- (grey): channel inactive 49
- 3.4 Configuration Tab 52
- [0] = OAMP (default) 65
- [1] = Media 65
- [2] = Control 65
- 3.4.2 Media Settings 67
- [2] Bypass 70
- [3] Events Only 70
- 3.4.3 Security Settings 79
- [1] Enable = Enabled 116
- [0] Disable (default) 116
- [1] Enable 116
- 5 steps: 120
- To the default Proxy 121
- 3.4.4.1.4 Coders 123
- 4 steps: 130
- 3.4.4.2.3 Metering Tones 144
- 3.4.4.2.5 Keypad Features 147
- 3.4.4.6.1 Authentication 175
- 3.4.4.6.2 Automatic Dialing 176
- 3.4.4.6.4 Call Forward 178
- 3.4.4.6.6 Call Waiting 180
- Disable (default) 188
- No = Don't register 189
- Yes = Register 189
- 3.4.5 Advanced Applications 190
- [1] Enable (Bellcore) 194
- [2] Ericsson MD-110 194
- [3] NEC (ICS) 194
- 3.5 Management Tab 198
- 3.5.1.3 Maintenance Actions 207
- 2 steps: 209
- 3.5.2 Software Update 210
- 3.6.2 Gateway Statistics 223
- 3.6.2.1 Call Counters 224
- 3.6.2.2 Call Routing Status 226
- 3.6.2.3 Registration Status 227
- 3.6.2.5 IP Connectivity 228
- 4 ini File Configuration 231
- 4.2 The ini File Structure 232
- 4.3 Modifying an ini File 235
- 4.4.1 Networking Parameters 236
- 4.4.2 System Parameters 244
- [0] = Disabled (default) 251
- 4.4.4 Security Parameters 252
- 4.4.5 RADIUS Parameters 257
- 4.4.6 SNMP Parameters 258
- [1] = Enabled 268
- Port = Port number 268
- UserId = User name 272
- UserPassword = Password 272
- 4.4.8 Voice Mail Parameters 277
- 4.4.9 PSTN Parameters 279
- [66] = TBR21 280
- Npi = Number Plan 297
- Ton = Type of Number 297
- 4.4.12 Channel Parameters 298
- [0] = Disable (default) 299
- [1] = Enable 299
- [1] Enable (default) 304
- 5 Default Settings 305
- 6.4 Coefficient File 312
- 6.5 User Information File 313
- 7 IP Telephony Capabilities 315
- 7.1.1 Configuring SAS 316
- 7.3.2.1 T.38 Fax Relay Mode 319
- 7.3.3 Supporting V.34 Faxes 324
- 7.4 FXO Operating Modes 326
- 7.4.1.1 One-Stage Dialing 327
- 7.4.1.2 Two-Stage Dialing 328
- 7.4.1.4 DID Wink 329
- 7.4.2 Telephone-to-IP Calls 330
- Connectivity and QoS) 335
- 7.11 Call Detail Record 339
- 7.13 Configuration Examples 342
- 7.14.3 Call Transfer 359
- 7.14.4 Call Forward 360
- 7.14.5 Call Waiting 361
- 7.14.7 Caller ID 362
- 8 Networking Capabilities 365
- 8.2.1 STUN 366
- 8.2.3 No-Op Packets 367
- 8.3 IP Multicasting 368
- 8.8 VLANS and Multiple IPs 370
- Control: Premium control 372
- Management: Bronze 372
- 10.1 MP-11x Specifications 381
- 10.2 MP-124 Specifications 384
- 11 Glossary 387
Relacionado con productos y manuales para Gateways / Controladores AudioCodes MediaPack 114
(44 paginas)
(44 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales