AudioCodes MediaPack 114 Manual de usuario Pagina 68
- Pagina / 390
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SIP User's Manual 68 Document #: LTRT-65411
MediaPack Series
2. Configure the Voice parameters according to the table below.
3. Click the Submit button to save your changes.
4. To save the changes to flash memory, refer to ''Saving Configuration'' on page 209.
Table 3-13:
Media Settings, Voice Settings Parameters
Parameter Description
Voice Volume
[VoiceVolume]
Voice gain control (in decibels). This parameter sets the level for
the transmitted (IP-to-Tel) signal.
The valid range is -32 to 31 dB. The default value is 0 dB.
Input Gain
[InputGain]
Pulse-code modulation (PCM) input gain control (in decibels).
This parameter sets the level for the received (Tel-to-IP) signal.
The valid range is -32 to 31 dB. The default value is 0 dB.
Silence Suppression
[EnableSilenceCompression]
Silence Suppression is a method for conserving bandwidth on
VoIP calls by not sending packets when silence is detected.
[0] Disable = Silence Suppression is disabled (default).
[1] Enable = Silence Suppression is enabled.
[2] Enable without Adaptation = A single silence packet is sent
during a silence period (applicable only to G.729).
Note: If the selected coder is G.729, the following rules determine
the value of the 'annexb' parameter of the fmtp attribute in the
SDP:
If EnableSilenceCompression is 0: 'annexb=no'.
If EnableSilenceCompression is 1: 'annexb=yes'.
If EnableSilenceCompression is 2 and IsCiscoSCEMode is 0:
'annexb=yes'.
If EnableSilenceCompression is 2 and IsCiscoSCEMode is 1:
'annexb=no'.
Echo Canceler
[EnableEchoCanceller]
Determines whether echo cancellation is enabled and therefore,
echo from voice calls is removed.
[0] Off = Echo Canceler is disabled.
[1] On = Echo Canceler is enabled (default).
Note: This parameter is used to maintain backward compatibility.
DTMF Transport Type
[DTMFTransportType]
Determines the DTMF transport type.
[0] DTMF Mute = Erases digits from voice stream and doesn't
relay to remote.
[2] Transparent DTMF = Digits remain in voice stream.
[3] RFC 2833 Relay DTMF = Erases digits from voice stream
and relays to remote according to RFC 2833 (default).
[7] RFC 2833 Relay Rcv Mute = DTMFs are sent according to
RFC 2833 and muted when received.
Note: This parameter is automatically updated if one of the
following parameters is configured: TxDTMFOption or
RxDTMFOption.
MF Transport Type
[MFTransportType]
Not Applicable.
- User's Manual 1
- Table of Contents 3
- List of Figures 8
- List of Tables 11
- WEEE EU Directive 13
- Customer Support 13
- Trademarks 13
- Related Documentation 14
- 1 Overview 15
- 1.2 MediaPack Features 16
- 1.3 SIP Overview 17
- Reader’s Notes 18
- 2 Configuration Concepts 19
- 3 Web-Based Management 21
- 3.3.1 Toolbar 24
- 3.3.2 Navigation Tree 25
- 3.3.3.1 Accessing Pages 28
- 3.3.3.2 Viewing Parameters 28
- 3.3.3.5 Working with Tables 32
- 3.3.5.1 Creating a Scenario 36
- 3.3.5.3 Editing a Scenario 39
- 3.3.5.6 Deleting a Scenario 42
- 3.3.7 Getting Help 47
- 3.3.8 Using the Home Page 48
- (grey): channel inactive 49
- 3.4 Configuration Tab 52
- [0] = OAMP (default) 65
- [1] = Media 65
- [2] = Control 65
- 3.4.2 Media Settings 67
- [2] Bypass 70
- [3] Events Only 70
- 3.4.3 Security Settings 79
- [1] Enable = Enabled 116
- [0] Disable (default) 116
- [1] Enable 116
- 5 steps: 120
- To the default Proxy 121
- 3.4.4.1.4 Coders 123
- 4 steps: 130
- 3.4.4.2.3 Metering Tones 144
- 3.4.4.2.5 Keypad Features 147
- 3.4.4.6.1 Authentication 175
- 3.4.4.6.2 Automatic Dialing 176
- 3.4.4.6.4 Call Forward 178
- 3.4.4.6.6 Call Waiting 180
- Disable (default) 188
- No = Don't register 189
- Yes = Register 189
- 3.4.5 Advanced Applications 190
- [1] Enable (Bellcore) 194
- [2] Ericsson MD-110 194
- [3] NEC (ICS) 194
- 3.5 Management Tab 198
- 3.5.1.3 Maintenance Actions 207
- 2 steps: 209
- 3.5.2 Software Update 210
- 3.6.2 Gateway Statistics 223
- 3.6.2.1 Call Counters 224
- 3.6.2.2 Call Routing Status 226
- 3.6.2.3 Registration Status 227
- 3.6.2.5 IP Connectivity 228
- 4 ini File Configuration 231
- 4.2 The ini File Structure 232
- 4.3 Modifying an ini File 235
- 4.4.1 Networking Parameters 236
- 4.4.2 System Parameters 244
- [0] = Disabled (default) 251
- 4.4.4 Security Parameters 252
- 4.4.5 RADIUS Parameters 257
- 4.4.6 SNMP Parameters 258
- [1] = Enabled 268
- Port = Port number 268
- UserId = User name 272
- UserPassword = Password 272
- 4.4.8 Voice Mail Parameters 277
- 4.4.9 PSTN Parameters 279
- [66] = TBR21 280
- Npi = Number Plan 297
- Ton = Type of Number 297
- 4.4.12 Channel Parameters 298
- [0] = Disable (default) 299
- [1] = Enable 299
- [1] Enable (default) 304
- 5 Default Settings 305
- 6.4 Coefficient File 312
- 6.5 User Information File 313
- 7 IP Telephony Capabilities 315
- 7.1.1 Configuring SAS 316
- 7.3.2.1 T.38 Fax Relay Mode 319
- 7.3.3 Supporting V.34 Faxes 324
- 7.4 FXO Operating Modes 326
- 7.4.1.1 One-Stage Dialing 327
- 7.4.1.2 Two-Stage Dialing 328
- 7.4.1.4 DID Wink 329
- 7.4.2 Telephone-to-IP Calls 330
- Connectivity and QoS) 335
- 7.11 Call Detail Record 339
- 7.13 Configuration Examples 342
- 7.14.3 Call Transfer 359
- 7.14.4 Call Forward 360
- 7.14.5 Call Waiting 361
- 7.14.7 Caller ID 362
- 8 Networking Capabilities 365
- 8.2.1 STUN 366
- 8.2.3 No-Op Packets 367
- 8.3 IP Multicasting 368
- 8.8 VLANS and Multiple IPs 370
- Control: Premium control 372
- Management: Bronze 372
- 10.1 MP-11x Specifications 381
- 10.2 MP-124 Specifications 384
- 11 Glossary 387
Relacionado con productos y manuales para Gateways / Controladores AudioCodes MediaPack 114
(44 paginas)
(44 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.436 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales