AudioCodes MediaPack 114 Manual de usuario Pagina 287
- Pagina / 390
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Version 5.6 287 November 2008
SIP User's Manual 4. ini File Configuration
Parameter Description
[0] = FSK-based signaling (default)
[1] = DTMF-based signaling
Note: This parameter is applicable only to FXS interfaces.
EnableDID
This ini file table parameter enables support for Japan NTT
'Modem' Direct Inward Dialing (DID). FXS interfaces can be
connected to Japan's NTT PBX using 'Modem' DID lines. These
DID lines are used to deliver a called number to the PBX. The DID
signal can be sent alone or combined with an NTT Caller ID signal.
The format of this parameter is as follows:
[EnableDID]
FORMAT EnableDID_Index = EnableDID_IsEnable,
EnableDID_Port, EnableDID_Module;
[\EnableDID]
Where,
IsEnable = Enables [1] or disables [0] (default) Japan NTT
Modem DID support.
Port = Port number.
Module = Module number (N/A).
For example:
[EnableDID]
EnableDID 0 = 1,2,$$;
[\EnableDID]
Notes:
This parameter is applicable only to FXS interfaces.
For an explanation on using ini file table parameters, refer to
''Structure of ini File Table Parameters'' on page 233.
EnableCallerIDTypeTwo
Disables the generation of Caller ID type 2 when the phone is off-
hooked. Caller ID type 2, also known as off-hook Caller ID is sent
to a currently busy telephone to display the caller ID of the waiting
call.
[0] = Caller ID type 2 isn't played.
[1] = Caller ID type 2 is played (default).
PolarityReversalType
Defines the voltage change slope during polarity reversal or wink.
[0] = Soft reverse polarity (default).
[1] = Hard reverse polarity.
Notes:
This parameter is applicable only to FXS interfaces.
Some Caller ID signals use reversal polarity and/or Wink
signals. In these cases, it is recommended to set
PolarityReversalType to 1 (Hard).
CurrentDisconnectDuration
The duration (in msec) of the current disconnect pulse.
The range is 200 to 1500. The default is 900.
Notes:
This parameter is applicable for both FXS and FXO interfaces.
The FXO interface detection range is approximately 200 msec
of the parameter's value plus 100. For example, if
- User's Manual 1
- Table of Contents 3
- List of Figures 8
- List of Tables 11
- WEEE EU Directive 13
- Customer Support 13
- Trademarks 13
- Related Documentation 14
- 1 Overview 15
- 1.2 MediaPack Features 16
- 1.3 SIP Overview 17
- Reader’s Notes 18
- 2 Configuration Concepts 19
- 3 Web-Based Management 21
- 3.3.1 Toolbar 24
- 3.3.2 Navigation Tree 25
- 3.3.3.1 Accessing Pages 28
- 3.3.3.2 Viewing Parameters 28
- 3.3.3.5 Working with Tables 32
- 3.3.5.1 Creating a Scenario 36
- 3.3.5.3 Editing a Scenario 39
- 3.3.5.6 Deleting a Scenario 42
- 3.3.7 Getting Help 47
- 3.3.8 Using the Home Page 48
- (grey): channel inactive 49
- 3.4 Configuration Tab 52
- [0] = OAMP (default) 65
- [1] = Media 65
- [2] = Control 65
- 3.4.2 Media Settings 67
- [2] Bypass 70
- [3] Events Only 70
- 3.4.3 Security Settings 79
- [1] Enable = Enabled 116
- [0] Disable (default) 116
- [1] Enable 116
- 5 steps: 120
- To the default Proxy 121
- 3.4.4.1.4 Coders 123
- 4 steps: 130
- 3.4.4.2.3 Metering Tones 144
- 3.4.4.2.5 Keypad Features 147
- 3.4.4.6.1 Authentication 175
- 3.4.4.6.2 Automatic Dialing 176
- 3.4.4.6.4 Call Forward 178
- 3.4.4.6.6 Call Waiting 180
- Disable (default) 188
- No = Don't register 189
- Yes = Register 189
- 3.4.5 Advanced Applications 190
- [1] Enable (Bellcore) 194
- [2] Ericsson MD-110 194
- [3] NEC (ICS) 194
- 3.5 Management Tab 198
- 3.5.1.3 Maintenance Actions 207
- 2 steps: 209
- 3.5.2 Software Update 210
- 3.6.2 Gateway Statistics 223
- 3.6.2.1 Call Counters 224
- 3.6.2.2 Call Routing Status 226
- 3.6.2.3 Registration Status 227
- 3.6.2.5 IP Connectivity 228
- 4 ini File Configuration 231
- 4.2 The ini File Structure 232
- 4.3 Modifying an ini File 235
- 4.4.1 Networking Parameters 236
- 4.4.2 System Parameters 244
- [0] = Disabled (default) 251
- 4.4.4 Security Parameters 252
- 4.4.5 RADIUS Parameters 257
- 4.4.6 SNMP Parameters 258
- [1] = Enabled 268
- Port = Port number 268
- UserId = User name 272
- UserPassword = Password 272
- 4.4.8 Voice Mail Parameters 277
- 4.4.9 PSTN Parameters 279
- [66] = TBR21 280
- Npi = Number Plan 297
- Ton = Type of Number 297
- 4.4.12 Channel Parameters 298
- [0] = Disable (default) 299
- [1] = Enable 299
- [1] Enable (default) 304
- 5 Default Settings 305
- 6.4 Coefficient File 312
- 6.5 User Information File 313
- 7 IP Telephony Capabilities 315
- 7.1.1 Configuring SAS 316
- 7.3.2.1 T.38 Fax Relay Mode 319
- 7.3.3 Supporting V.34 Faxes 324
- 7.4 FXO Operating Modes 326
- 7.4.1.1 One-Stage Dialing 327
- 7.4.1.2 Two-Stage Dialing 328
- 7.4.1.4 DID Wink 329
- 7.4.2 Telephone-to-IP Calls 330
- Connectivity and QoS) 335
- 7.11 Call Detail Record 339
- 7.13 Configuration Examples 342
- 7.14.3 Call Transfer 359
- 7.14.4 Call Forward 360
- 7.14.5 Call Waiting 361
- 7.14.7 Caller ID 362
- 8 Networking Capabilities 365
- 8.2.1 STUN 366
- 8.2.3 No-Op Packets 367
- 8.3 IP Multicasting 368
- 8.8 VLANS and Multiple IPs 370
- Control: Premium control 372
- Management: Bronze 372
- 10.1 MP-11x Specifications 381
- 10.2 MP-124 Specifications 384
- 11 Glossary 387
Relacionado con productos y manuales para Gateways / Controladores AudioCodes MediaPack 114
(44 paginas)
(44 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.100 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales